Neueste Beiträge

Seiten: 1 ... 6 7 [8] 9 10
71
Sundtek MediaTV Pro / Re: DVB-S2 UsbStick defekt Hardware?
« Letzter Beitrag von HannMuell am Februar 25, 2026, 12:27:49 Nachmittag »
wenn ich parrallel zum verbose start von mediasrv einen testscan mache kommt das bei medisrv:
Code: [Auswählen]
2026-02-25 11:25:42 [270529] IR Setup
2026-02-25 11:25:42 [270529] Initializing Remote Control Support (interrupt)
2026-02-25 11:25:42 [270529] registered virtual: /dev/mediainput0
2026-02-25 11:25:42 [270529] registering: adapter0/0
2026-02-25 11:25:42 [270529] registered virtual: /dev/dvb/adapter0/frontend0
2026-02-25 11:25:42 [270529] registered virtual: /dev/dvb/adapter0/demux0
2026-02-25 11:25:42 [270529] registered virtual: /dev/dvb/adapter0/dvr0
2026-02-25 11:25:42 [270529] Driver loaded within 2373 milliseconds
2026-02-25 11:25:47 [270529] Initial devicescan done, switching detection mode
2026-02-25 11:25:57 [270529] [FE0] . o ( Enabling Standby ) o .
2026-02-25 11:25:57 [270529] [FE0] Set Voltage off
2026-02-25 11:26:30 [270529] [FE0] . o ( Waking up from standby ) o .
2026-02-25 11:26:30 [270529] [FE0] Set Voltage off
2026-02-25 11:26:30 [270529] INIT_DTV: 0
2026-02-25 11:26:30 [270529] Starting transfer
2026-02-25 11:26:30 [270529] ignoring dvr cmd: 40106f52
2026-02-25 11:26:30 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:30 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:30 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 40106f52
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 40106f52
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 40106f52
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 40106f52
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] INIT_DTV: 0
2026-02-25 11:26:33 [270529] Starting transfer
2026-02-25 11:26:50 [270529] [FE0] . o ( Enabling Standby ) o .
2026-02-25 11:26:50 [270529] [FE0] Set Voltage off
72
Sundtek MediaTV Pro / Re: DVB-S2 UsbStick defekt Hardware?
« Letzter Beitrag von HannMuell am Februar 25, 2026, 12:25:53 Nachmittag »
Code: [Auswählen]
/opt/bin# ./mediasrv -v
2026-02-25 11:24:31 [270299] UID: 0 SUID 0
2026-02-25 11:24:31 [270299] Alsa Blocking on (default)
2026-02-25 11:24:31 [270299] Starting up Multimedia Framework (Jan 24 2026 00:58:34)
2026-02-25 11:24:31 [270299] Semaphore exists, removing and reallocating it
2026-02-25 11:24:31 [270299] Detected DVB version.h
2026-02-25 11:24:31 [270300] Starting service processor (PID 270300)
2026-02-25 11:24:31 [270299] API Version: 5.12
2026-02-25 11:24:31 [270299] Running on Linux (6.12.69+deb13-amd64)
2026-02-25 11:24:31 [270299] Detected: AuthenticAMD
2026-02-25 11:24:31 [270299] This CPU supports: MMX, SSE, SSE2
2026-02-25 11:24:31 [270299] scanning devices
2026-02-25 11:24:31 [270299]
2026-02-25 11:24:31 [270299] Scanning for drivers
2026-02-25 11:24:31 [270299] found lib: libdrv_fm.so
2026-02-25 11:24:31 [270299] found lib: libdrv_fm_dab_dabplus.so
2026-02-25 11:24:31 [270299] found lib: libdrv_net.so
2026-02-25 11:24:31 [270299] found lib: libdrv_tntdvb.so
2026-02-25 11:24:31 [270299] found lib: libdrv_vivi.so
2026-02-25 11:24:31 [270299] found lib: libdrv_hikarisoft_isdb.so
2026-02-25 11:24:31 [270299] found lib: libdrv_ngTV.so
2026-02-25 11:24:31 [270299] found lib: libdrv_em28xx.so
2026-02-25 11:24:31 [270299] found lib: libdrv_eLight.so
2026-02-25 11:24:31 [270299]
2026-02-25 11:24:31 [270299] Scanning for plugins
2026-02-25 11:24:31 [270299]
2026-02-25 11:24:31 [270299] Starting up device manager
2026-02-25 11:24:32 [270299] registering ID: 0
2026-02-25 11:24:32 [270299] Memory mapped transfers are not available
2026-02-25 11:24:32 [270299] Board config found: Sundtek SkyTV 8 (eLight)
2026-02-25 11:24:32 [270299] This board provides 1 frontends
2026-02-25 11:24:32 [270299]
2026-02-25 11:24:32 [270299] registering bandwidth report
2026-02-25 11:24:32 [270299] Initializing SYSV-IPC
2026-02-25 11:24:32 [270299] Allocation using pg for type 65678
2026-02-25 11:24:32 [270299] scanning devices done
2026-02-25 11:24:32 [270299] attached devices:
2026-02-25 11:24:32 [270300] Autostarting scripts in /etc/sundtek/
2026-02-25 11:24:32 [270300] executed all available items
2026-02-25 11:24:34 [270299] demodulator successfully attached (DVB_S/S2)!
2026-02-25 11:24:34 [270299]
2026-02-25 11:24:34 [270299] Vertical Polarisation is set to 13.00 Volt
2026-02-25 11:24:34 [270299] Horizontal Polarisation is set to 19.80 Volt
2026-02-25 11:24:34 [270299] Current limit is set to 400 mA
2026-02-25 11:24:34 [270299]
2026-02-25 11:24:34 [270299] Using Sundtek remote control layout
2026-02-25 11:24:34 [270299]
2026-02-25 11:24:34 [270299] IR Setup
2026-02-25 11:24:34 [270299] Initializing Remote Control Support (interrupt)
2026-02-25 11:24:34 [270299] Unable to create /dev/mediainput0 (17/File exists)
2026-02-25 11:24:34 [270299] registered virtual: /dev/mediainput0
2026-02-25 11:24:34 [270299] registering: adapter0/0
2026-02-25 11:24:34 [270299] registered virtual: /dev/dvb/adapter0/frontend0
2026-02-25 11:24:34 [270299] registered virtual: /dev/dvb/adapter0/demux0
2026-02-25 11:24:34 [270299] registered virtual: /dev/dvb/adapter0/dvr0
2026-02-25 11:24:34 [270299] Driver loaded within 2425 milliseconds
2026-02-25 11:24:39 [270299] Initial devicescan done, switching detection mode
2026-02-25 11:24:49 [270299] [FE0] . o ( Enabling Standby ) o .
2026-02-25 11:24:49 [270299] [FE0] Set Voltage off
73
Sundtek MediaTV Pro / Re: DVB-S2 UsbStick defekt Hardware?
« Letzter Beitrag von Sundtek am Februar 25, 2026, 12:22:19 Nachmittag »
Du kannst den Treiber auch mal manuell starten und schauen ob es Fehlermeldungen gibt. Die Grüne LED ist eigentlich schon mal gut.

sudo -s
cd /opt/bin
killall -9 mediasrv
./mediaclient --shutdown # falls es auf dem System kein killall gibt
./mediasrv -v

74
Sundtek MediaTV Pro / Re: DVB-S2 UsbStick defekt Hardware?
« Letzter Beitrag von HannMuell am Februar 25, 2026, 12:17:33 Nachmittag »
Also LNB Signal kann ich ausschliessen.
Koax habe ich am Fernseher entnommen. Das Signal funktioneirt vorher noch am TV.
12V Habe ich das alte gemesse, hatte 12V.
Habe gestern ein neues 12V umgebaut (also alter Stecker auf neues 12V Netzteil) - weil ich dachte dass evtl zu wenig Strom fließt / Netzteil defekt ist.
Also auch dass neue Netzteil führt zu dem selben Verhalten.
Netzteil kann ich mit sehr hoher Wahrscheinlichkeit also auch ausschliessen

Während dem ausführen der beiden Befehle leuchtet die LED grün.

75
Sundtek MediaTV Pro / Re: DVB-S2 UsbStick defekt Hardware?
« Letzter Beitrag von Sundtek am Februar 25, 2026, 12:12:11 Nachmittag »
Der Tuner wird also erst mal erkannt, scheinbar liegt aber kein Signal an oder das 12V Netzteil ist nicht angeschlossen. Welche Farbe hat das LED während die letzten beiden Tests gemacht werden? Das LED schaltet sich nach 15 Sekunden aus sofern keine Applikation drauf zugreift (=> Standby).

Prüfe erst mal in der Richtung.
76
Sundtek MediaTV Pro / Re: DVB-S2 UsbStick defekt Hardware?
« Letzter Beitrag von HannMuell am Februar 25, 2026, 12:09:05 Nachmittag »
/opt/bin/mediaclient --testastra -d /dev/dvb/adapter0/dvr0
Testing Astra 19.2 Frequencies
DVBS
LO Band / 18V:
Checking for lock:
..........
LO Band / 13V:
Checking for lock:
..........
HI Band / 18V:
Checking for lock:
..........
HI Band / 13V:
Checking for lock:
..........
DVB-S2 ZDF HD / 18V
Checking for lock:
..........


/opt/bin/mediaclient --tsscan /dev/dvb/adapter0/dvr0
media scan tp: 0
Timed out after 1 seconds
Total found: 0 PMTs (incl. unknown 0x0000)
Scan finished after 0 packets (0 bytes)



Editiert von Sundtek: hatte hier die falschen Befehle gegeben - hat sich in den Folgebeiträgen aufgeklärt
77
Sundtek MediaTV Pro / Re: DVB-S2 UsbStick defekt Hardware?
« Letzter Beitrag von Sundtek am Februar 25, 2026, 12:02:21 Nachmittag »
Und was zeigen folgende Befehle an:
/opt/bin/mediaclient --testastra -d /dev/dvb/adapter0/frontend0
/opt/bin/mediaclient --tsscan /dev/dvb/adapter0/dvr0

Aktualisiert - es hat sich später in dem Beitrag herausgestellt dass ich das falsche Device Interface angegeben habe
78
Sundtek MediaTV Pro / Re: DVB-S2 UsbStick defekt Hardware?
« Letzter Beitrag von HannMuell am Februar 25, 2026, 11:58:32 Vormittag »
dmesg
Code: [Auswählen]
[754653.361037] random: crng reseeded on system resumption
[754653.361629] PM: suspend exit
[754661.932400] audit: type=1400 audit(1772013169.280:403): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266772 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[754661.932503] audit: type=1400 audit(1772013169.280:404): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266772 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=1000 ouid=0
[754661.999899] audit: type=1400 audit(1772013169.348:405): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266778 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[754661.999917] audit: type=1400 audit(1772013169.348:406): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266778 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=0 ouid=0
[754662.018454] audit: type=1400 audit(1772013169.364:407): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266781 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[754662.018473] audit: type=1400 audit(1772013169.364:408): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266781 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=0 ouid=0
[754664.538369] audit: type=1400 audit(1772013171.884:409): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266785 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[754664.538389] audit: type=1400 audit(1772013171.884:410): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266785 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=1000 ouid=0
[754667.783528] usb 3-2: new high-speed USB device number 51 using xhci_hcd
[754668.299813] usb 3-2: New USB device found, idVendor=2659, idProduct=1805, bcdDevice= 0.00
[754668.299831] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[754668.299838] usb 3-2: Product: eLight
[754668.299844] usb 3-2: Manufacturer: Sundtek
[754668.299850] usb 3-2: SerialNumber: U181219014137
[754670.738638] usb 3-2: usbfs: process 180681 (mediasrv) did not claim interface 0 before use
[754670.820466] input: Sundtek Remote Control as /devices/virtual/input/input67
[754679.263900] wlp1s0: authenticate with 2c:91:ab:85:67:ef (local address=f4:b3:01:d8:6b:c0)
[754679.267332] wlp1s0: send auth to 2c:91:ab:85:67:ef (try 1/3)
[754679.297244] wlp1s0: authenticated
[754679.299081] wlp1s0: associate with 2c:91:ab:85:67:ef (try 1/3)
[754679.301835] wlp1s0: RX AssocResp from 2c:91:ab:85:67:ef (capab=0x1111 status=0 aid=4)
[754679.318908] wlp1s0: associated
[754679.363666] wlp1s0: Limiting TX power to 20 (23 - 3) dBm as advertised by 2c:91:ab:85:67:ef
[754694.494065] audit: type=1400 audit(1772013201.840:411): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267023 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[754694.494085] audit: type=1400 audit(1772013201.840:412): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267023 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=0 ouid=0
[754697.178464] audit: type=1400 audit(1772013204.524:413): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267024 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[754697.178480] audit: type=1400 audit(1772013204.524:414): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267024 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=0 ouid=0
[754697.227709] audit: type=1400 audit(1772013204.576:415): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267025 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[754697.227728] audit: type=1400 audit(1772013204.576:416): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267025 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=0 ouid=0

mediaclient -e
Code: [Auswählen]
**** List of Media Hardware Devices ****
device 0: [              eLight]  DVB-S/S2, REMOTE-CONTROL
  [INFO]:
     STATUS: STANDBY
  [BUS]:
     ID: 3-2
  [SERIAL]:
     ID: U181219014137
  [DVB-S/S2]:
     FESTATUS: STANDBY
     LNBVOLTAGE: DISABLED
     LNBSUPPLY: USBPOWER
     LNBSTATUS: OK
     FRONTEND: /dev/dvb/adapter0/frontend0
     DVR: /dev/dvb/adapter0/dvr0
     DMX: /dev/dvb/adapter0/demux0
  [REMOTECONTROL]:
     INPUT0: /dev/mediainput0

lsusb
Code: [Auswählen]
Bus 003 Device 051: ID 2659:1805 Sundtek eLight
79
Sundtek MediaTV Pro / Re: DVB-S2 UsbStick defekt Hardware?
« Letzter Beitrag von Sundtek am Februar 25, 2026, 11:32:20 Vormittag »
Hallo,

was zeigen folgende Befehle an:

sudo dmesg
/opt/bin/mediaclient -e
lsusb

Aus welchem Jahr ist der Tuner / welcher Tuner ist das überhaupt?
80
Sundtek MediaTV Pro / DVB-S2 UsbStick defekt Hardware?
« Letzter Beitrag von HannMuell am Februar 25, 2026, 11:27:00 Vormittag »
HI!

seit Kurzem funktioniert mein USB‑DVB‑S2‑Stick leider nicht mehr. Das Gerät wird zwar vom System erkannt, jedoch nicht ordnungsgemäß eingehängt. In MediaClient erscheint kein entsprechendes Gerät.

Das LED‑Signal leuchtet nur schwach rot. Ich habe bereits das Netzteil überprüft und ein neues ausprobiert, jedoch besteht das Problem weiterhin.

Könnten Sie mir bitte weiterhelfen, woran die Ursache liegen könnte und welche Schritte zur Fehlerbehebung Sie empfehlen?

Vielen Dank im Voraus für Ihre Unterstützung.
Seiten: 1 ... 6 7 [8] 9 10