Beiträge anzeigen

Diese Sektion erlaubt es ihnen alle Beiträge dieses Mitglieds zu sehen. Beachten sie, dass sie nur solche Beiträge sehen können, zu denen sie auch Zugriffsrechte haben.


Themen - Want2Play

Seiten: [1]
1
Hello,

The remote command of my Media TV Pro III (bought in 2016) is no more usable since the batteries are dead. I use VDR with the distribution https://www.minidvblinux.de/ on a Raspberry Pi3.

I've try to change the configuration of VDR in the "Remote" setup and set the remote type to 0,1,2,3 (and reboot) without result.

I've installed the driver on my Linux box (x86) : Debian Buster/stable.
  • I would know how to reset the remote command to the original configuration with the new batteries.
  • What is the simplest solution to test the remote command in Linux, I'm using Debian Buster (stable) ?

2
Software / Tvheadend and the options "Low Noise Amplifier / LNA" and "Power save"
« am: Januar 13, 2016, 04:13:31 Nachmittag »
Hi,

I'm using :
* Sundtek MediaPro III
* Raspberry Pi 2
* 3 A / 5 V power supply
* Osmc (November 2015)
* Tvheadend
* external hard drive with power supply
* /sys/devices/system/cpu/cpu[0-9]*/cpufreq/scaling_governor in "performance" mode

In Tvheadend, for the tuner's configuration there is the options :
* Low Noise Amplifier (LNA)
* Power saving

What is the good settings for this options ?



Somewhere, I found "DiseqC", I understand that it's for the satellite (DVB-S), so nothing to do with this. I'm right or not ?

3
Hello,

I have two problem after some hours : the system freeze or VDR (VNSI) say "no data" and it is impossible to access at a channel.

The configuration :
- Raspberry 2;
- Power 5 V / 2A;
- the MerdiaPro III is connected to a powered Hub USB;
- SD cards "SanDisk Ultra microSDXC UHS-I card 64 GB (Up to 48 MB/S)"
- Openelec 6.0.0;
- VDR backend + VDR frontend (VDSI) "Priority -1" "Demander le différé 1" , IP by default not modified 127.0.0.1;
- MediaPro configured for DVB-T with "Enable hardware PID = ON", "Enable IR Receiver = ON", "Enable suspend/resume the driver = ON";
- the last version of the Sundtek driver is used : manual update via the GUI;
- some plugins in the "Video" section;


I have a freeze of the image after some hours or it's impossible to obtain a channel.

The details now.

Problem 1 :
After some hours, 5 hours in the last case, and with a HD channel (ARTE HD) selected, the image an the sound are stopped. The image is static on the screen. Impossible to stop or change the channel. The reboot is the only solution.

Problem 2 :
Some records are scheduled by the "Guide" menu in the night and are correctly done. But in the morning, it's impossible to see a channel. The VDR frontend (VDSI) report "No data" for each channel. The reboot is the only solution.

I don't know if it's related to your hardware or software, I could post in the Openelec forum if your are not concern. I hope that you can help me.

Edit : With Overclock Turob or Pi2 or no overclock, I notice that the CPU frequency could by 100 MHz or 900 Mhz, but sometimes the frequency is 600 MHz and return to 900 or 100 MHz. The temperature is between 42 °C or 50 °C - Pi2 mode without dissipators. I can't say why.
I've try to use the "performance" option (https://www.raspberrypi.org/forums/viewtopic.php?f=29&t=128872&p=872235#p872235) : "echo performance > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor" for each CPU, but the default "ondemand" value is set at the boot time.

If I can give you some other usefull informations, ask them please.

Best regards.



4
Software / Raspberry PI2 + Openelec 6.0 + MediaPro III + VDR + Remote command
« am: Dezember 30, 2015, 07:16:17 Nachmittag »
Hello,

Edit : I use a Raspberry Pi2

I'm using Openelec 6.0.0 and the VDR backend and frontend.  I've the last version of the remote command, the version "3" from a german thread.

The cursors can change the channels, but the number can't select a channel. After I want map some key to the Kodi interface.

I've found this, but it could be too old for the 6.0.0 version of OpenElec http://openelec.tv/forum/103-infared-remotes/61729-sundtek-remote-not-working?start=15

How to activate the remote command in OpenElec / VDR ?

Thanks.

Best regards.



Seiten: [1]