Beiträge anzeigen

Diese Sektion erlaubt es ihnen alle Beiträge dieses Mitglieds zu sehen. Beachten sie, dass sie nur solche Beiträge sehen können, zu denen sie auch Zugriffsrechte haben.


Nachrichten - linron

Seiten: [1]
1
{Single, Dual, Quad} Sundtek SkyTV Ultimate / Re:Qnap 259 Pro+ -> TVHeadend -> Sundtek DVS-S/S2 (III) Problem
« am: April 23, 2013, 04:56:44 Nachmittag »
es liegt meines Erachtens nicht an den Parametern sondern dass das QPKG nicht mit DVB-S/S2 Support compiliert wurde. Es laufen wohl nur DVB-T & DVB-C Sticks damit...

2
Dreambox Settopbox / Re:Dreambox DM7020s Enigma1 per Netzwerk mit Sundtek SkyTV Ultimate?!
« am: Dezember 11, 2012, 03:04:45 Nachmittag »
d.h. auch wenn ich den Stick nicht direkt per USB an der Dreambox betreiben will sondern übers Netzwerk mounten möchte ist dies bei Enigma1 nicht möglich?!  ???

3
{Single, Dual, Quad} Sundtek SkyTV Ultimate / Re:Qnap 259 Pro+ -> TVHeadend -> Sundtek DVS-S/S2 (III) Problem
« am: Dezember 11, 2012, 12:16:56 Nachmittag »
es scheint wohl an dem TVHeadend-QPKG zu liegen. Mit einer XBMC-Frodo Installation auf meinem Laptop lässt sich der Sundtek Stick per Netzwerk mounten und auch dort in TVHeadend einbinden.. Was mich nur wundert ist das mehrere Qnap Besitzer hier geschrieben haben das sie es zum laufen gebracht haben. Da ich ein Linux-Newbie bin weiß ich nicht wie ich mir selber ein TVHeadend für die Qnap kompilieren kann. Wäre super wenn sich hier ein Qnap Besitzer findet der Lust hat mir zu helfen  ;D

4
Dreambox Settopbox / Dreambox DM7020s Enigma1 per Netzwerk mit Sundtek SkyTV Ultimate?!
« am: Dezember 11, 2012, 12:08:38 Nachmittag »
Ist es möglich einen Sundtek SkyTV Ultimate per Netzwerk an einer alten Enigma1 Dreambox zu betreiben?! Die Box hat nur einen DVB-S Tuner und es wäre toll wenn man dadurch DVB-S2 für HD Sender über die Box gucken könnte! Daher mal die generelle Frage ob dies möglich ist...

Habe mal versucht den Treiber zu installieren -> Hier der Output:

root@dm7020:/tmp> wget http://www.sundtek.de/media/sundtek_netinst.sh
Connecting to www.sundtek.de[85.10.198.106]:80
sundtek_netinst.sh   100% |**********************************************************************************************************************************************************| 82310       00:00 ETA        |     0       --:-- ETA
root@dm7020:/tmp> chmod 777 sundtek_netinst.sh
root@dm7020:/tmp> ./sundtek_netinst.sh
Busybox installation

Welcome to the Sundtek linux driver setup
(C)opyright 2008-2012 Sundtek <kontakt@sundtek.de>

Legal notice:
This software comes without any warranty, use it at your own risk

Please note it's only allowed to use this driver package with devices from
authorized distributors or from Sundtek Germany
The Virtual analogTV Grabber (vivi) might be used freely for testing purpose

Do you want to continue [Y/N]:
Nutzungsbedingungen:
Sundtek übernimmt keinerlei Haftung für Schäden welche eventuell durch
das System oder die angebotenen Dateien entstehen können.

Dieses Softwarepaket darf ausschließlich mit Geraeten von authorisierten
Distributoren oder Sundtek Deutschland verwendet werden
Der Virtuelle AnalogTV Treiber (vivi) kann für Testzwecke ohne jegliche
Restriktionen verwendet werden

Wollen Sie fortfahren [J/N]:
j
unpacking...
checking system... testing libc OK 2.3.90
PPC32 System detected
installing (netinstall mode) ...
Connecting to www.sundtek.de[85.10.198.106]:80
installer.tar.gz     100% |**********************************************************************************************************************************************************|  1079 KB    00:00 ETA        |     0       --:-- ETA
finalizing configuration... (can take a few seconds) 
Starting driver...
modprobe: module usbcore not found.
modprobe: failed to load module usbcore
modprobe: module ehci-hcd not found.
modprobe: failed to load module ehci-hcd
done.
root@dm7020:/tmp>


bin leider ein linux newbie und wäre für hilfe dankbar!!!

5
{Single, Dual, Quad} Sundtek SkyTV Ultimate / Re:Qnap 259 Pro+ -> TVHeadend -> Sundtek DVS-S/S2 (III) Problem
« am: November 23, 2012, 03:51:46 Nachmittag »
ok, habe ich nun ausgeführt:
/opt/bin/mediaclient --ts-settle-timeout=2000 -d /dev/dvb/adapter0/frontend0

anschließend den Qnap gebootet und TVHeadend wieder aktiviert.

meine sundtek.conf sieht noch immer so aus:
loglevel=min
device_attach=/share/MD0_DATA/.qpkg/TVH_Dev_Sundtek/restart_tvh.sh
enablenetwork=on

die mediasrv.log läuft nun nicht mehr voll sondern zeigt folgendes:

[/share/MD0_DATA/.qpkg/TVH_Dev_Sundtek] # cat mediasrv.log
2012-11-23 14:27:32 [10859] Starting up Multimedia Framework (Nov 13 2012 17:49:10)
2012-11-23 14:27:32 [10859]
2012-11-23 14:27:32 [10859] *** Autostarting Networksupport ***
2012-11-23 14:27:32 [10859]
2012-11-23 14:27:32 [10859] API Version: 5.5
2012-11-23 14:27:32 [10859] Running on Linux (2.6.33.2)
2012-11-23 14:27:32 [10859] Detected: GenuineIntel
2012-11-23 14:27:32 [10859] This CPU supports: MMX and SSE
2012-11-23 14:27:32 [10859] scanning devices
2012-11-23 14:27:32 [10859]
2012-11-23 14:27:32 [10859] Scanning for drivers
2012-11-23 14:27:32 [10859] found lib: libdrv_fm.so
2012-11-23 14:27:32 [10861] Starting service processor (PID 10861)
2012-11-23 14:27:32 [10859] found lib: libdrv_hikarisoft_isdb.so
2012-11-23 14:27:32 [10859] found lib: libdrv_em28xx.so
2012-11-23 14:27:32 [10859] found lib: libdrv_vivi.so
2012-11-23 14:27:32 [10859] found lib: libdrv_net.so
2012-11-23 14:27:32 [10859] found lib: libdrv_tntdvb.so
2012-11-23 14:27:32 [10859] found lib: libdrv_ngTV.so
2012-11-23 14:27:32 [10859]
2012-11-23 14:27:32 [10859] Scanning for plugins
2012-11-23 14:27:32 [10859] found lib: libencoder_plugin.so
2012-11-23 14:27:32 [10859] MediaAVPlugin: MPEG Encoder
2012-11-23 14:27:32 [10859] Copyright: (C) Tpe 2011/2012
2012-11-23 14:27:32 [10859]
2012-11-23 14:27:32 [10859] Starting up device manager
2012-11-23 14:27:32 [10859] unable to open /dev/misc
2012-11-23 14:27:32 [10859] scanning devices done
2012-11-23 14:27:32 [10859] attached devices:
2012-11-23 14:27:32 [10859] Starting listener
2012-11-23 14:27:32 [10859] Listening on 9234
2012-11-23 14:27:32 [10859] registering ID: 0
2012-11-23 14:27:32 [10859] disconnecting kernel driver
2012-11-23 14:27:32 [10861] Autostarting scripts in /etc/sundtek/
2012-11-23 14:27:32 [10861] executed all available items
2012-11-23 14:27:32 [10859] received notification client request
2012-11-23 14:27:33 [10859] attaching second generation DVB-S/S2 demodulator
2012-11-23 14:27:36 [10859] demodulator successfully attached (DVB_S/S2)!
2012-11-23 14:27:36 [10859] Allocation using pg for type 65678
2012-11-23 14:27:36 [10859] requesting to attach tuner(s) now
2012-11-23 14:27:36 [10859] registering: adapter0/0
2012-11-23 14:27:36 [10859] registered virtual: /dev/dvb/adapter0/frontend0
2012-11-23 14:27:36 [10859] registered virtual: /dev/dvb/adapter0/demux0
2012-11-23 14:27:36 [10859] registered virtual: /dev/dvb/adapter0/dvr0
2012-11-23 14:27:36 [10859] Setting RC Protocol to NEC
2012-11-23 14:27:36 [10859] registered virtual: /dev/mediainput0
2012-11-23 14:27:36 [10859] Remote Control Layout: 0
2012-11-23 14:27:36 [10861] trying to load uinput module
2012-11-23 14:27:36 [10861] loading uinput kernel extention failed, remote control will not work with lirc
2012-11-23 14:27:36 [10859] No remote control support available
2012-11-23 14:27:36 [10859] Trying to load ffmpeg codecs
2012-11-23 14:27:36 [10859] could not load libavutil.so
2012-11-23 14:27:36 [10859] could not load libswscale.so
2012-11-23 14:27:36 [10859] could not load libavcodec.so
2012-11-23 14:27:36 [10859] could not load libavformat.so
2012-11-23 14:27:36 [10859] AnalogTV encoding won't be possible in driver's side
2012-11-23 14:27:36 [10859]
2012-11-23 14:27:36 [10859] Sundtek MediaTV Driver loaded. This driver is licensed for non-commercial use
2012-11-23 14:27:36 [10859] with Sundtek MediaTV only
2012-11-23 14:27:36 [10859] Driver loaded within 4008 milliseconds
2012-11-23 14:27:36 [10859] Serial(0): U120411121134
2012-11-23 14:27:36 [10859] received device attach message
2012-11-23 14:27:36 [10861] notify request: media device connected
2012-11-23 14:27:39 [10859] Initial devicescan done, switching detection mode
2012-11-23 14:27:51 [10859] Enabling standby
2012-11-23 14:27:51 [10859] Device is now in standby
2012-11-23 14:30:31 [10859] Waking up device
2012-11-23 14:30:33 [10859] voltage is off


Beim Versuch den MUX (Delivery System:) manuell hinzuzufügen bekomme ich leider noch immer die Felermeldung:

/dvb/feopts/delsys/_dev_dvb_adapter0_Sundtek_DVB_S_S2__III_ -- 400


[/share/MD0_DATA/.qpkg/TVH_Dev_Sundtek] # /opt/bin/mediaclient --readsignal=0 -d /dev/dvb/adapter0/frontend0 --band UNIVERSAL
== reading digital TV signal ==
SIGNAL: [                                 ] (  0%)  BER:      0 FREQ: 9750000    Hz LOCKED:  NO SYS: DVB-S2 SYM: 0 FEC: FEC_NONE MOD: QPSK VOLTAGE: OFF TONE: OFF
SIGNAL: [                                 ] (  0%)  BER:      0 FREQ: 9750000    Hz LOCKED:  NO SYS: DVB-S2 SYM: 0 FEC: FEC_NONE MOD: QPSK VOLTAGE: OFF TONE: OFF
SIGNAL: [                                 ] (  0%)  BER:      0 FREQ: 9750000    Hz LOCKED:  NO SYS: DVB-S2 SYM: 0 FEC: FEC_NONE MOD: QPSK VOLTAGE: OFF TONE: OFF
SIGNAL: [                                 ] (  0%)  BER:      0 FREQ: 9750000    Hz LOCKED:  NO SYS: DVB-S2 SYM: 0 FEC: FEC_NONE MOD: QPSK VOLTAGE: OFF TONE: OFF
SIGNAL: [                                 ] (  0%)  BER:      0 FREQ: 9750000    Hz LOCKED:  NO SYS: DVB-S2 SYM: 0 FEC: FEC_NONE MOD: QPSK VOLTAGE: OFF TONE: OFF
SIGNAL: [                                 ] (  0%)  BER:      0 FREQ: 9750000    Hz LOCKED:  NO SYS: DVB-S2 SYM: 0 FEC: FEC_NONE MOD: QPSK VOLTAGE: OFF TONE: OFF



und nun ?!  :'( eine Idee woran es liegen könnte oder wie ich weiter vorgehen sollte?!


6
{Single, Dual, Quad} Sundtek SkyTV Ultimate / Re:Qnap 259 Pro+ -> TVHeadend -> Sundtek DVS-S/S2 (III) Problem
« am: November 23, 2012, 02:38:53 Nachmittag »
irgendwie scheint es als würden die Einträge nicht ziehen. Trotz:

[/] # /opt/bin/mediaclient --loglevel=off
switching off loglevel
[/] # /opt/bin/mediaclient --ts-settle-timeout=2000
Using device: /dev/dvb/adapter0/frontend0
[/] #  /opt/bin/mediaclient --enablenetwork=off
Disabling network support

sieht meine sundtek.conf so aus:

[/] # cat /etc/sundtek.conf
#
#
loglevel=min
device_attach=/share/MD0_DATA/.qpkg/TVH_Dev_Sundtek/restart_tvh.sh
enablenetwork=on

werde ich jetzt mal manuell wie vorgeschlagen ändern auf:
#
loglevel=off
ts_settle_timeout=2000
device_attach=/share/MD0_DATA/.qpkg/TVH_Dev_Sundtek/restart_tvh.sh
enablenetwork=off

RICHTIG?! Hier noch ein paar Debuginfo's:

[/share/MD0_DATA/.qpkg/TVH_Dev_Sundtek] # /opt/bin/mediaclient --readsignal=0 -d /dev/dvb/adapter0/frontend0 --band UNIVERSAL
== reading digital TV signal ==
SIGNAL: [..............................   ] ( 90%)  BER:      0 FREQ: 12551500   Hz LOCKED: YES SYS: DVB-S2 SYM: 22000000 FEC: FEC_5_6 MOD: QPSK VOLTAGE: V(13V) TONE: ON
SIGNAL: [..............................   ] ( 90%)  BER:      0 FREQ: 12551500   Hz LOCKED: YES SYS: DVB-S2 SYM: 22000000 FEC: FEC_5_6 MOD: QPSK VOLTAGE: V(13V) TONE: ON
SIGNAL: [..............................   ] ( 90%)  BER:      0 FREQ: 12551500   Hz LOCKED: YES SYS: DVB-S2 SYM: 22000000 FEC: FEC_5_6 MOD: QPSK VOLTAGE: V(13V) TONE: ON
SIGNAL: [..............................   ] ( 90%)  BER:      0 FREQ: 12551500   Hz LOCKED: YES SYS: DVB-S2 SYM: 22000000 FEC: FEC_5_6 MOD: QPSK VOLTAGE: V(13V) TONE: ON
SIGNAL: [..............................   ] ( 90%)  BER:      0 FREQ: 12551500   Hz LOCKED: YES SYS: DVB-S2 SYM: 22000000 FEC: FEC_5_6 MOD: QPSK VOLTAGE: V(13V) TONE: ON
SIGNAL: [..............................   ] ( 90%)  BER:      0 FREQ: 12551500   Hz LOCKED: YES SYS: DVB-S2 SYM: 22000000 FEC: FEC_5_6 MOD: QPSK VOLTAGE: V(13V) TONE: ON
SIGNAL: [..............................   ] ( 90%)  BER:      0 FREQ: 12551500   Hz LOCKED: YES SYS: DVB-S2 SYM: 22000000 FEC: FEC_5_6 MOD: QPSK VOLTAGE: V(13V) TONE: ON
SIGNAL: [..............................   ] ( 90%)  BER:      0 FREQ: 12551500   Hz LOCKED: YES SYS: DVB-S2 SYM: 22000000 FEC: FEC_5_6 MOD: QPSK VOLTAGE: V(13V) TONE: ON
SIGNAL: [..............................   ] ( 90%)  BER:      0 FREQ: 12551500   Hz LOCKED: YES SYS: DVB-S2 SYM: 22000000 FEC: FEC_5_6 MOD: QPSK VOLTAGE: V(13V) TONE: ON
SIGNAL: [..............................   ] ( 90%)  BER:      0 FREQ: 12551500   Hz LOCKED: YES SYS: DVB-S2 SYM: 22000000 FEC: FEC_5_6 MOD: QPSK VOLTAGE: V(13V) TONE: ON
SIGNAL: [..............................   ] ( 90%)  BER:      0 FREQ: 12551500   Hz LOCKED: YES SYS: DVB-S2 SYM: 22000000 FEC: FEC_5_6 MOD: QPSK VOLTAGE: V(13V) TONE: ON

[/] # /opt/bin/mediaclient -e
**** List of Media Hardware Devices ****
device 0: [Sundtek SkyTV Ultimate III (USB 2.0)]  DVB-S/S2, REMOTE-CONTROL
  [SERIAL]:
     ID: XXXX
  [DVB-S/S2]:
     FRONTEND: /dev/dvb/adapter0/frontend0
     DVR: /dev/dvb/adapter0/dvr0
     DMX: /dev/dvb/adapter0/demux0
  [REMOTECONTROL]:
     INPUT0: /dev/mediainput0

   
   
[/] # mediaclient --lc
**** List of Media Clients ****
/dev/dvb/adapter0/frontend0:
  6026 ... tvheadend
/dev/dvb/adapter0/dvr0:
  6026 ... tvheadend
/dev/dvb/adapter0/demux0:
  No client connected
/dev/mediainput0:
  No client connected
 
[/] # top

Mem: 916552K used, 105148K free, 0K shrd, 86088K buff, 482768K cached
Load average: 0.00, 0.13, 0.24    (State: S=sleeping R=running, W=waiting)

  PID USER     STATUS   RSS  PPID %CPU %MEM COMMAND
16661 admin    S       5760     1 35.5  0.5 mediasrv
 6026 admin    S       5036     1  1.9  0.4 tvheadend

7
{Single, Dual, Quad} Sundtek SkyTV Ultimate / Qnap 259 Pro+ -> TVHeadend -> Sundtek DVS-S/S2 (III) Problem
« am: November 23, 2012, 01:44:02 Nachmittag »
Hallo,

habe gerade meinen neuen Sundtek DVS-S/S2 (III) erhalten und leider schon das erste Problem  :'( daher hoffe ich auf Support! Nun zu den Details:

Qnap 259 Pro+ Firmwareversion: 3.8.0 Build 20121114
# uname -a
Linux 2.6.33.2 #1 SMP Wed Nov 14 03:31:11 CST 2012 i686 unknown
[/] # cat proc/version
Linux version 2.6.33.2 (root@NasX86-10) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Wed Nov 14 03:31:11 CST 2012

Stick: Sundtek DVS-S/S2 (III)

installierte QPKG's:

TVH_Dev_Sundtek_0.4
TVHeadend_0.5.0_x86
xmltv_0.3_x86

befolgte Anleitung:

Als erstes muss man in tvheadend unter Konfiguration - TV Adapter - Sat config die LNB anlegen. (nur ASTRA)
Name: LNB1 (oder was auch immer)
Switchport: 0 (ist der erste diseqc Port)
LNB Type: universal

default war bereits hinterlegt

Nun sollte man eigentlich auf General - Add DVB Network by location - den Satellit raussuchen und unten in diesem Fenster in der Liste das soeben angelegte LNB1 auswählen.
Damit wird der initiale Transponder definiert. Aber das funktioniert bei Astra nicht, es werden nur die Hälfte der Transponder gefunden.
Also diesen Schritt weglassen.

Nun siehst du im Reiter Multiplexes nach. Wenn da schon welche drinstehen, alle markieren und löschen.

Nun legt man den initialen Transponder einfach manuell an.
Unter Multiplexes - Add Muxes manually:

Für Astra 19,2 folgendes eingeben:
"frequency": 11953500,
"symbol_rate": 27500000,
"fec": "3/4",
"polarisation": "Horizontal",
"modulation oder constellation": "QPSK",
"delivery_system": "SYS_DVBS", -> nicht auswählbar!!! Fehlermeldung: /dvb/feopts/delsys/_dev_dvb_adapter0_Sundtek_DVB_S_S2__III_ -- 400
Satellite config: LNB1 oder was du vorher definiert hast für Astra



Zusammenfassung:

beim Versuch unter "delivery_system" etwas hinzuzufügen erscheint die Fehlermeldung:
/dvb/feopts/delsys/_dev_dvb_adapter0_Sundtek_DVB_S_S2__III_ -- 400

[/share/MD0_DATA/.qpkg/TVH_Dev_Sundtek] # more mediasrv.log
2012-11-22 20:50:58 [16661] Starting up Multimedia Framework (Nov 13 2012 17:49:10)
2012-11-22 20:50:58 [16661]
2012-11-22 20:50:58 [16661] *** Autostarting Networksupport ***
2012-11-22 20:50:58 [16661]
2012-11-22 20:50:58 [16661] API Version: 5.5
2012-11-22 20:50:58 [16661] Running on Linux (2.6.33.2)
2012-11-22 20:50:58 [16661] Detected: GenuineIntel
2012-11-22 20:50:58 [16661] This CPU supports: MMX and SSE
2012-11-22 20:50:58 [16661] scanning devices
2012-11-22 20:50:58 [16661]
2012-11-22 20:50:58 [16661] Scanning for drivers
2012-11-22 20:50:58 [16661] found lib: libdrv_fm.so
2012-11-22 20:50:58 [16661] found lib: libdrv_hikarisoft_isdb.so
2012-11-22 20:50:58 [16661] found lib: libdrv_em28xx.so
2012-11-22 20:50:58 [16661] found lib: libdrv_vivi.so
2012-11-22 20:50:58 [16661] found lib: libdrv_net.so
2012-11-22 20:50:58 [16661] found lib: libdrv_tntdvb.so
2012-11-22 20:50:58 [16661] found lib: libdrv_ngTV.so
2012-11-22 20:50:58 [16661]
2012-11-22 20:50:58 [16661] Scanning for plugins
2012-11-22 20:50:58 [16661] found lib: libencoder_plugin.so
2012-11-22 20:50:58 [16661] MediaAVPlugin: MPEG Encoder
2012-11-22 20:50:58 [16661] Copyright: (C) Tpe 2011/2012
2012-11-22 20:50:58 [16661]
2012-11-22 20:50:58 [16661] Starting up device manager
2012-11-22 20:50:58 [16664] Starting service processor (PID 16664)
2012-11-22 20:50:58 [16661] unable to open /dev/misc
2012-11-22 20:50:58 [16661] scanning devices done
2012-11-22 20:50:58 [16661] attached devices:
2012-11-22 20:50:58 [16661] Starting listener
2012-11-22 20:50:58 [16661] registering ID: 0
2012-11-22 20:50:58 [16661] Listening on 9234
2012-11-22 20:50:58 [16661] disconnecting kernel driver
2012-11-22 20:50:58 [16664] Autostarting scripts in /etc/sundtek/
2012-11-22 20:50:58 [16664] executed all available items
2012-11-22 20:50:58 [16661] received notification client request
2012-11-22 20:50:59 [16661] attaching second generation DVB-S/S2 demodulator
2012-11-22 20:51:02 [16661] demodulator successfully attached (DVB_S/S2)!
2012-11-22 20:51:02 [16661] Allocation using pg for type 65678
2012-11-22 20:51:02 [16661] requesting to attach tuner(s) now
2012-11-22 20:51:02 [16661] registering: adapter0/0
2012-11-22 20:51:02 [16661] registered virtual: /dev/dvb/adapter0/frontend0
2012-11-22 20:51:02 [16661] registered virtual: /dev/dvb/adapter0/demux0
2012-11-22 20:51:02 [16661] registered virtual: /dev/dvb/adapter0/dvr0
2012-11-22 20:51:02 [16661] Setting RC Protocol to NEC
2012-11-22 20:51:02 [16661] registered virtual: /dev/mediainput0
2012-11-22 20:51:02 [16661] Remote Control Layout: 0
2012-11-22 20:51:02 [16664] trying to load uinput module
2012-11-22 20:51:02 [16664] loading uinput kernel extention failed, remote control will not work with lirc
2012-11-22 20:51:02 [16661] No remote control support available
2012-11-22 20:51:02 [16661] Trying to load ffmpeg codecs
2012-11-22 20:51:02 [16661] could not load libavutil.so
2012-11-22 20:51:02 [16661] could not load libswscale.so
2012-11-22 20:51:02 [16661] could not load libavcodec.so
2012-11-22 20:51:02 [16661] could not load libavformat.so
2012-11-22 20:51:02 [16661] AnalogTV encoding won't be possible in driver's side
2012-11-22 20:51:02 [16661]
2012-11-22 20:51:02 [16661] Sundtek MediaTV Driver loaded. This driver is licensed for non-commercial use
2012-11-22 20:51:02 [16661] with Sundtek MediaTV only
2012-11-22 20:51:02 [16661] Driver loaded within 4007 milliseconds
2012-11-22 20:51:02 [16661] Serial(0): XXXX
2012-11-22 20:51:02 [16661] received device attach message
2012-11-22 20:51:02 [16664] notify request: media device connected
2012-11-22 20:51:05 [16661] Initial devicescan done, switching detection mode
2012-11-22 20:51:17 [16661] Enabling standby
2012-11-22 20:51:17 [16661] Device is now in standby
2012-11-22 20:55:14 [16661] Waking up device
2012-11-22 20:55:15 [16661] voltage is off
2012-11-22 21:08:18 [16661] voltage is low/0
2012-11-22 21:08:18 [16661] Diseqc execution time: 92 ms
2012-11-22 21:08:18 [16661] diseqc send burst Unmodulated (SEC_MINI_A)
2012-11-22 21:08:18 [16661] Frequency: 1951
2012-11-22 21:08:18 [16661] Symbolrate: 22000
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (2068 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (2374 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (3192 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (3568 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (3776 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (4324 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (4523 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (5452 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (5824 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (6016 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (6768 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (7180 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (7708 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (7918 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (8173 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (8648 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (9057 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (9588 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (9842 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (10528 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (10917 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (11280 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (11663 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (11942 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (12220 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (13160 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (13368 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (14100 // 0)
2012-11-22 21:08:19 [16661] TS Sync byte not aligned, realigning stream (14565 // 0)



!!!!!!!!!!!!!!!!!!  HILFE !!!!!!!!!!!!!!!


mediasrv.log bereits 1336305355 bytes groß (TVHEADEND nun wieder disabled) damit die Logs nicht noch mehr Platz einnehmen....

Zur Info: Quad LNB (Astra) -> diseqc schalter hängt im Dachgeschoss dran weil ich irgendwann mal einen zweiten SAT dran hängen wollte.
Sat-Kabel hängt an einer Dreambox DM7020s (kein DVB-S2, guter Empfang)

Sundtek DVS-S/S2 (III) hängt am Netzteil und ist per USB mit dem QNAP verbunden.
SAT KABEL zum Sundtek provisorisch vom SAT-OUT der Dreambox genommen (hatte bereits mal eine DBOX2 so hinter der Dreambox in Betrieb -> Dreambox dabei im Standby)

Seiten: [1]