DVB-S2 UsbStick defekt Hardware?

[HannMuell]

HI!

seit Kurzem funktioniert mein USB‑DVB‑S2‑Stick leider nicht mehr. Das Gerät wird zwar vom System erkannt, jedoch nicht ordnungsgemäß eingehängt. In MediaClient erscheint kein entsprechendes Gerät.

Das LED‑Signal leuchtet nur schwach rot. Ich habe bereits das Netzteil überprüft und ein neues ausprobiert, jedoch besteht das Problem weiterhin.

Könnten Sie mir bitte weiterhelfen, woran die Ursache liegen könnte und welche Schritte zur Fehlerbehebung Sie empfehlen?

Vielen Dank im Voraus für Ihre Unterstützung.

[Sundtek]

Hallo,

was zeigen folgende Befehle an:

sudo dmesg
/opt/bin/mediaclient -e
lsusb

Aus welchem Jahr ist der Tuner / welcher Tuner ist das überhaupt?

[HannMuell]

dmesg

Code: [Auswählen]

[754653.361037] random: crng reseeded on system resumption
[754653.361629] PM: suspend exit
[754661.932400] audit: type=1400 audit(1772013169.280:403): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266772 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[754661.932503] audit: type=1400 audit(1772013169.280:404): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266772 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=1000 ouid=0
[754661.999899] audit: type=1400 audit(1772013169.348:405): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266778 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[754661.999917] audit: type=1400 audit(1772013169.348:406): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266778 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=0 ouid=0
[754662.018454] audit: type=1400 audit(1772013169.364:407): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266781 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[754662.018473] audit: type=1400 audit(1772013169.364:408): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266781 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=0 ouid=0
[754664.538369] audit: type=1400 audit(1772013171.884:409): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266785 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[754664.538389] audit: type=1400 audit(1772013171.884:410): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=266785 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=1000 ouid=0
[754667.783528] usb 3-2: new high-speed USB device number 51 using xhci_hcd
[754668.299813] usb 3-2: New USB device found, idVendor=2659, idProduct=1805, bcdDevice= 0.00
[754668.299831] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[754668.299838] usb 3-2: Product: eLight
[754668.299844] usb 3-2: Manufacturer: Sundtek
[754668.299850] usb 3-2: SerialNumber: U181219014137
[754670.738638] usb 3-2: usbfs: process 180681 (mediasrv) did not claim interface 0 before use
[754670.820466] input: Sundtek Remote Control as /devices/virtual/input/input67
[754679.263900] wlp1s0: authenticate with 2c:91:ab:85:67:ef (local address=f4:b3:01:d8:6b:c0)
[754679.267332] wlp1s0: send auth to 2c:91:ab:85:67:ef (try 1/3)
[754679.297244] wlp1s0: authenticated
[754679.299081] wlp1s0: associate with 2c:91:ab:85:67:ef (try 1/3)
[754679.301835] wlp1s0: RX AssocResp from 2c:91:ab:85:67:ef (capab=0x1111 status=0 aid=4)
[754679.318908] wlp1s0: associated
[754679.363666] wlp1s0: Limiting TX power to 20 (23 - 3) dBm as advertised by 2c:91:ab:85:67:ef
[754694.494065] audit: type=1400 audit(1772013201.840:411): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267023 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[754694.494085] audit: type=1400 audit(1772013201.840:412): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267023 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=0 ouid=0
[754697.178464] audit: type=1400 audit(1772013204.524:413): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267024 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[754697.178480] audit: type=1400 audit(1772013204.524:414): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267024 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=0 ouid=0
[754697.227709] audit: type=1400 audit(1772013204.576:415): apparmor="ALLOWED" operation="open" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267025 comm="unix_chkpwd" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[754697.227728] audit: type=1400 audit(1772013204.576:416): apparmor="ALLOWED" operation="file_mmap" class="file" profile="unix-chkpwd" name="/opt/lib/libmediaclient.so" pid=267025 comm="unix_chkpwd" requested_mask="rm" denied_mask="rm" fsuid=0 ouid=0

mediaclient -e

Code: [Auswählen]

**** List of Media Hardware Devices ****
device 0: [              eLight]  DVB-S/S2, REMOTE-CONTROL
  [INFO]:
     STATUS: STANDBY
  [BUS]:
     ID: 3-2
  [SERIAL]:
     ID: U181219014137
  [DVB-S/S2]:
     FESTATUS: STANDBY
     LNBVOLTAGE: DISABLED
     LNBSUPPLY: USBPOWER
     LNBSTATUS: OK
     FRONTEND: /dev/dvb/adapter0/frontend0
     DVR: /dev/dvb/adapter0/dvr0
     DMX: /dev/dvb/adapter0/demux0
  [REMOTECONTROL]:
     INPUT0: /dev/mediainput0

lsusb

Code: [Auswählen]

Bus 003 Device 051: ID 2659:1805 Sundtek eLight


[Sundtek]

Und was zeigen folgende Befehle an:
/opt/bin/mediaclient --testastra -d /dev/dvb/adapter0/frontend0
/opt/bin/mediaclient --tsscan /dev/dvb/adapter0/dvr0

Aktualisiert - es hat sich später in dem Beitrag herausgestellt dass ich das falsche Device Interface angegeben habe

[HannMuell]

/opt/bin/mediaclient --testastra -d /dev/dvb/adapter0/dvr0
Testing Astra 19.2 Frequencies
DVBS
LO Band / 18V:
Checking for lock:
..........
LO Band / 13V:
Checking for lock:
..........
HI Band / 18V:
Checking for lock:
..........
HI Band / 13V:
Checking for lock:
..........
DVB-S2 ZDF HD / 18V
Checking for lock:
..........


/opt/bin/mediaclient --tsscan /dev/dvb/adapter0/dvr0
media scan tp: 0
Timed out after 1 seconds
Total found: 0 PMTs (incl. unknown 0x0000)
Scan finished after 0 packets (0 bytes)



Editiert von Sundtek: hatte hier die falschen Befehle gegeben - hat sich in den Folgebeiträgen aufgeklärt

[Sundtek]

Der Tuner wird also erst mal erkannt, scheinbar liegt aber kein Signal an oder das 12V Netzteil ist nicht angeschlossen. Welche Farbe hat das LED während die letzten beiden Tests gemacht werden? Das LED schaltet sich nach 15 Sekunden aus sofern keine Applikation drauf zugreift (=> Standby).

Prüfe erst mal in der Richtung.

[HannMuell]

Also LNB Signal kann ich ausschliessen.
Koax habe ich am Fernseher entnommen. Das Signal funktioneirt vorher noch am TV.
12V Habe ich das alte gemesse, hatte 12V.
Habe gestern ein neues 12V umgebaut (also alter Stecker auf neues 12V Netzteil) - weil ich dachte dass evtl zu wenig Strom fließt / Netzteil defekt ist.
Also auch dass neue Netzteil führt zu dem selben Verhalten.
Netzteil kann ich mit sehr hoher Wahrscheinlichkeit also auch ausschliessen

Während dem ausführen der beiden Befehle leuchtet die LED grün.

[Sundtek]

Du kannst den Treiber auch mal manuell starten und schauen ob es Fehlermeldungen gibt. Die Grüne LED ist eigentlich schon mal gut.

sudo -s
cd /opt/bin
killall -9 mediasrv
./mediaclient --shutdown # falls es auf dem System kein killall gibt
./mediasrv -v

[HannMuell]

Code: [Auswählen]

/opt/bin# ./mediasrv -v
2026-02-25 11:24:31 [270299] UID: 0 SUID 0
2026-02-25 11:24:31 [270299] Alsa Blocking on (default)
2026-02-25 11:24:31 [270299] Starting up Multimedia Framework (Jan 24 2026 00:58:34)
2026-02-25 11:24:31 [270299] Semaphore exists, removing and reallocating it
2026-02-25 11:24:31 [270299] Detected DVB version.h
2026-02-25 11:24:31 [270300] Starting service processor (PID 270300)
2026-02-25 11:24:31 [270299] API Version: 5.12
2026-02-25 11:24:31 [270299] Running on Linux (6.12.69+deb13-amd64)
2026-02-25 11:24:31 [270299] Detected: AuthenticAMD
2026-02-25 11:24:31 [270299] This CPU supports: MMX, SSE, SSE2
2026-02-25 11:24:31 [270299] scanning devices
2026-02-25 11:24:31 [270299]
2026-02-25 11:24:31 [270299] Scanning for drivers
2026-02-25 11:24:31 [270299] found lib: libdrv_fm.so
2026-02-25 11:24:31 [270299] found lib: libdrv_fm_dab_dabplus.so
2026-02-25 11:24:31 [270299] found lib: libdrv_net.so
2026-02-25 11:24:31 [270299] found lib: libdrv_tntdvb.so
2026-02-25 11:24:31 [270299] found lib: libdrv_vivi.so
2026-02-25 11:24:31 [270299] found lib: libdrv_hikarisoft_isdb.so
2026-02-25 11:24:31 [270299] found lib: libdrv_ngTV.so
2026-02-25 11:24:31 [270299] found lib: libdrv_em28xx.so
2026-02-25 11:24:31 [270299] found lib: libdrv_eLight.so
2026-02-25 11:24:31 [270299]
2026-02-25 11:24:31 [270299] Scanning for plugins
2026-02-25 11:24:31 [270299]
2026-02-25 11:24:31 [270299] Starting up device manager
2026-02-25 11:24:32 [270299] registering ID: 0
2026-02-25 11:24:32 [270299] Memory mapped transfers are not available
2026-02-25 11:24:32 [270299] Board config found: Sundtek SkyTV 8 (eLight)
2026-02-25 11:24:32 [270299] This board provides 1 frontends
2026-02-25 11:24:32 [270299]
2026-02-25 11:24:32 [270299] registering bandwidth report
2026-02-25 11:24:32 [270299] Initializing SYSV-IPC
2026-02-25 11:24:32 [270299] Allocation using pg for type 65678
2026-02-25 11:24:32 [270299] scanning devices done
2026-02-25 11:24:32 [270299] attached devices:
2026-02-25 11:24:32 [270300] Autostarting scripts in /etc/sundtek/
2026-02-25 11:24:32 [270300] executed all available items
2026-02-25 11:24:34 [270299] demodulator successfully attached (DVB_S/S2)!
2026-02-25 11:24:34 [270299]
2026-02-25 11:24:34 [270299] Vertical Polarisation is set to 13.00 Volt
2026-02-25 11:24:34 [270299] Horizontal Polarisation is set to 19.80 Volt
2026-02-25 11:24:34 [270299] Current limit is set to 400 mA
2026-02-25 11:24:34 [270299]
2026-02-25 11:24:34 [270299] Using Sundtek remote control layout
2026-02-25 11:24:34 [270299]
2026-02-25 11:24:34 [270299] IR Setup
2026-02-25 11:24:34 [270299] Initializing Remote Control Support (interrupt)
2026-02-25 11:24:34 [270299] Unable to create /dev/mediainput0 (17/File exists)
2026-02-25 11:24:34 [270299] registered virtual: /dev/mediainput0
2026-02-25 11:24:34 [270299] registering: adapter0/0
2026-02-25 11:24:34 [270299] registered virtual: /dev/dvb/adapter0/frontend0
2026-02-25 11:24:34 [270299] registered virtual: /dev/dvb/adapter0/demux0
2026-02-25 11:24:34 [270299] registered virtual: /dev/dvb/adapter0/dvr0
2026-02-25 11:24:34 [270299] Driver loaded within 2425 milliseconds
2026-02-25 11:24:39 [270299] Initial devicescan done, switching detection mode
2026-02-25 11:24:49 [270299] [FE0] . o ( Enabling Standby ) o .
2026-02-25 11:24:49 [270299] [FE0] Set Voltage off


[HannMuell]

wenn ich parrallel zum verbose start von mediasrv einen testscan mache kommt das bei medisrv:

Code: [Auswählen]

2026-02-25 11:25:42 [270529] IR Setup
2026-02-25 11:25:42 [270529] Initializing Remote Control Support (interrupt)
2026-02-25 11:25:42 [270529] registered virtual: /dev/mediainput0
2026-02-25 11:25:42 [270529] registering: adapter0/0
2026-02-25 11:25:42 [270529] registered virtual: /dev/dvb/adapter0/frontend0
2026-02-25 11:25:42 [270529] registered virtual: /dev/dvb/adapter0/demux0
2026-02-25 11:25:42 [270529] registered virtual: /dev/dvb/adapter0/dvr0
2026-02-25 11:25:42 [270529] Driver loaded within 2373 milliseconds
2026-02-25 11:25:47 [270529] Initial devicescan done, switching detection mode
2026-02-25 11:25:57 [270529] [FE0] . o ( Enabling Standby ) o .
2026-02-25 11:25:57 [270529] [FE0] Set Voltage off
2026-02-25 11:26:30 [270529] [FE0] . o ( Waking up from standby ) o .
2026-02-25 11:26:30 [270529] [FE0] Set Voltage off
2026-02-25 11:26:30 [270529] INIT_DTV: 0
2026-02-25 11:26:30 [270529] Starting transfer
2026-02-25 11:26:30 [270529] ignoring dvr cmd: 40106f52
2026-02-25 11:26:30 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:30 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:30 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 40106f52
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 40106f52
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:31 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 40106f52
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 40106f52
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:32 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] ignoring dvr cmd: 80046f45
2026-02-25 11:26:33 [270529] INIT_DTV: 0
2026-02-25 11:26:33 [270529] Starting transfer
2026-02-25 11:26:50 [270529] [FE0] . o ( Enabling Standby ) o .
2026-02-25 11:26:50 [270529] [FE0] Set Voltage off


[Sundtek]

Ah sehr gut, ich habe das falsche Gerät angegeben, mein Fehler

Es sollte frontend0 sein und nicht dvr0, dvr0 versteht die Steuerbefehle nicht:

/opt/bin/mediaclient --testastra -d /dev/dvb/adapter0/frontend0
/opt/bin/mediaclient --tsscan /dev/dvb/adapter0/dvr0

dvr0 = da kommen die Daten raus
frontend0 = Steuerung des Tuners

[HannMuell]

Code: [Auswählen]

/opt/bin/mediaclient --testastra -d /dev/dvb/adapter0/frontend0
Testing Astra 19.2 Frequencies
DVBS
LO Band / 18V:
Checking for lock:
. [LOCKED]
LO Band / 13V:
Checking for lock:
. [LOCKED]
HI Band / 18V:
Checking for lock:
. [LOCKED]
HI Band / 13V:
Checking for lock:
. [LOCKED]
DVB-S2 ZDF HD / 18V
Checking for lock:
. [LOCKED]


/opt/bin/mediaclient --tsscan /dev/dvb/adapter0/dvr0

Code: [Auswählen]

media scan tp: 0
** NO GROUP GIVEN **
** NO GROUP GIVEN **
** NO GROUP GIVEN **
** NO GROUP GIVEN **
** NO GROUP GIVEN **
** NO GROUP GIVEN **
PMT PID: 0x17d4
  Program Number: 0x2b66
  TransportstreamID: 1011
  Encrypted: No
  Service type: 19
  Service running: Yes
  Provider Name: ZDFvision
  Service Name: ZDF HD
    --> 0x17f3 (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 PES packets containing private data)
    --> 0x17f4 (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 PES packets containing private data)
    --> 0x181a (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 private_sections)
    --> 0x181b (ISO/IEC 13818-6 type B)
    --> 0x181c (ISO/IEC 13818-6 type C)
    --> 0x17de (27)
    --> 0x17e8 (ISO/IEC 11172 Audio)
    --> 0x17e9 (ISO/IEC 11172 Audio)
    --> 0x17eb (ISO/IEC 11172 Audio)
    --> 0x17ea (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 PES packets containing private data)
    --> 0x17f2 (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 PES packets containing private data)
PMT PID: 0x189c
  Program Number: 0x2b7a
  TransportstreamID: 1011
  Encrypted: No
  Service type: 19
  Service running: Yes
  Provider Name: ZDFvision
  Service Name: zdf_neo HD
    --> 0x18bb (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 PES packets containing private data)
    --> 0x18e2 (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 private_sections)
    --> 0x18e3 (ISO/IEC 13818-6 type B)
    --> 0x18e4 (ISO/IEC 13818-6 type C)
    --> 0x18a6 (27)
    --> 0x18b0 (ISO/IEC 11172 Audio)
    --> 0x18b1 (ISO/IEC 11172 Audio)
    --> 0x18b3 (ISO/IEC 11172 Audio)
    --> 0x18b2 (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 PES packets containing private data)
    --> 0x18ba (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 PES packets containing private data)
PMT PID: 0x1af4
  Program Number: 0x2bb6
  TransportstreamID: 1011
  Encrypted: No
  Service type: 2
  Service running: Yes
  Provider Name: ZDFvision
  Service Name: Dlf Kultur
    --> 0x1af5 (ISO/IEC 11172 Audio)
    --> 0x1afb (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 private_sections)
PMT PID: 0x1afe
  Program Number: 0x2bb7
  TransportstreamID: 1011
  Encrypted: No
  Service type: 2
  Service running: Yes
  Provider Name: ZDFvision
  Service Name: Dlf
    --> 0x1aff (ISO/IEC 11172 Audio)
    --> 0x1b05 (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 private_sections)
PMT PID: 0x1b08
  Program Number: 0x2bb8
  TransportstreamID: 1011
  Encrypted: No
  Service type: 2
  Service running: Yes
  Provider Name: ZDFvision
  Service Name: Dlf Nova
    --> 0x1b09 (ISO/IEC 11172 Audio)
    --> 0x1b0f (ITU-T Rec. H.222.0 | ISO/IEC 13818-1 private_sections)
PMT PID: 0x1b12
  Program Number: 0x2bb9
  TransportstreamID: 1011
  Encrypted: No
  Service type: 2
  Service running: Yes
  Provider Name: ZDFvision
  Service Name: DRadio Dok&Deb
    --> 0x1b13 (ISO/IEC 11172 Audio)
Total found: 6 PMTs (incl. unknown 0x0000)
Scan finished after 35 packets (6580 bytes)

[Sundtek]

Ok also der Tuner funktioniert, das waren die technischen Standard-Tests um die Funktionalität des Tuners zu testen.

Womit hast Du jetzt Probleme?

[HannMuell]

Okay. Dann schicke ich dem Schwiegervater den Stick zurück und versuche aus der Ferne den Stick mit TVHeadend und docker wieder zum laufen zu bekommen.
Vielleicht hat sich im docker image auch irgendwas geänder warum er nicht mehr richtig tunen konnte.

Muss ich debuggen. Melde mich dann wenn ich mehr weiß.
BTW: gibt es einen offiziellen weg TVHeadend Docker zu nutzen?

ich hatte immer ein custom image generiert - das hat eigentlich immer funktioniert:
DOCKERFILE

Code: [Auswählen]

FROM linuxserver/tvheadend:latest
COPY sundtek/sundtek_netinst.sh /sundtek/
RUN yes Y | sh /sundtek/sundtek_netinst.sh -docker -use-custom-path=/sundtek
compose:

Code: [Auswählen]

  tvheadend:
    container_name: tvheadend
    build: ./tvheadend
    privileged: true
    environment:
      - PUID=1000
      - PGID=1000
      - TZ=Europe/Berlin
    volumes:
      - /home/xxx/.docker/tvheadend/config:/config
      - /home/xxx/.docker/tvheadend/picons:/picons
      - /mnt/recordings:/recordings
      - /etc/localtime:/etc/localtime:ro
    ports:
      - 9981:9981
      - 9982:9982
    devices:
      - /dev/dvb:/dev/dvb
      - /dev/bus/usb
      - /dev/dri/renderD128:/dev/dri/renderD128
      - /dev/dri/card0:/dev/dri/card0
    restart: unless-stopped

[Sundtek]

Bitte beachten, auf dem Host müssen auch /dev/dvb/adapterN nodes vorhanden sein bevor das Docker System gestartet wird.

Der Treiber kann das auf dem Host erstellen.
cd /tmp
wget http://sundtek.de/media/sundtek_netinst.sh
chmod +x sundtek_netinst.sh
./sundtek_netinst.sh -dockerhost