##Enable listening on network#enablenetwork=[on|off] #default: off
## sundtek.conf## ----- GLOBAL SECTION -----#Set loglevel for logging to /var/log/mediasrv.log#loglevel=[off|max] #default: min #max .. little bit more debug#bulk_notification[on|off] #default off, bulk_notification will only trigger device_attach once #after the the first device scan when the driver is started up #after this first scan, the notification will be triggered #normally again for each device. # #for example when 2 devices are attached to the system only one #notification will be triggered initially, any at a later time #attached device will generate another device_attach notification #by default each device will call the script which is set up with #device_attach#use_hwpidfilter=[on|off] #For DVB-C, DVB-T, DVB-S/S2 #enable PID filter, please be careful with that, there are only 15 HW Pid filters available #when more than 15 pids are set up the pid filter will be disabled automatically#dmhwpidfilter=[on|off] #default on, in some cases off might be useful to disable hw pid filter for settopboxes #if you get a black image when capturing a TV channel and watching another channel on the #same transponder - try this option and reboot#usb_transaction_delay=[0-20] #throttle the USB setup transactions, this can solve problems with weak USB stacks for #example for embedded boards, unit is milliseconds#usb_timeout=[0 - N] #USB timeout for each transaction in milliseconds, 0 default infinite#voltage_tone_off=[1 or 0] #0 .. default, normal behaviour #1 .. force DVB-S/S2 to not use any Voltage or Tone (ignore any user parameters) #ir_disabled=[1 or 0] #0 .. enable remote control polling, the driver will permanently check for remote control keys #1 .. disable remote control polling, might fix bugs with weak USB stacks on embedded boards##Enable listening on network#enablenetwork=[on|off] #default: off#Lowest adapter number to start with, e.g. /dev/dvb/adapter5/frontend0#first_adapter=5#Lowest videodevice number to start with, e.g. /dev/video5#first_videodev=5#Call attach script when new device appears#device_attach=[PATH_TO_SCRIPT] [PARAMETER|DEVID] #"DEVID" will automatically be replaced with the device ID#Call detach script when device disappears#device_detach=[PATH_TO_SCRIPT] [PARAMETER|DEVID] #"DEVID" will automatically be replaced with the device ID#Dreambox especially for DM800HD (not SE!)#vtuner_acceleration=[on|off] #default off, accelerate Dreambox 800HD datatransfer between USB Stick and #DM800HD# ----- Section for adapter with [SERIALNUMBER] -----#Get adapter serial number with /opt/bin/mediaclient -e#[SERIALNUMBER]#Description register as dreambox tuner#dreambox_support_fe1=[on|off] #default: off#Infrared protocol to use#ir_protocol=[RC5|NEC|RC6] #default: NEC#Keymap to use, e.g. "/lib/udev/rc_keymaps/vp702x"#rcmap=[PATH_TO_KEYMAP] #default: keymap which comes with the device#Choose initial DVB mode for hybrid DVB-T/DVB-C devices only#initial_dvb_mode=[DVBC|DVBT]#Call attach script when new device appears#device_attach=[PATH_TO_SCRIPT] [PARAMETER|DEVID] #"DEVID" will automatically be replaced with the device ID#Call detach script when device disappears#device_detach=[PATH_TO_SCRIPT] [PARAMETER|DEVID] #"DEVID" will automatically be replaced with the device ID#disable_atv=[0|1] #disable initialization of analogTV Frontend#Initial Audio Volume level for DVB-C/T Hybrid devices#volume=[0-127] #default: 118# WSS callback (see http://en.wikipedia.org/wiki/Widescreen_signaling)# trigger script when the videoformat changes between 16:9 or 4:3#wss_callback=[scriptname]# WSS_4_3_FULL# WSS_14_9_LETTERBOX_CENTRE# WSS_14_9_LETTERBOX_TOP# WSS_16_9_LETTERBOX_CENTRE# WSS_16_9_LETTERBOX_TOP# WSS_16_9_LETTERBOX_DEEPER# WSS_14_9_FULL_HEIGHT_4_3# WSS_16_9_FULL_HEIGHT_16_9# WSS_UNABLE_TO_DEMODULATE#Timeout in ms after that WSS_UNABLE_TO_DEMODULATE will be called#wss_demodulation_timeout=[MILLISECONDS] #vtuner_skip0=vtuner0 # skip /dev/misc/vtuner0 can also be vtunerN#vtuner_skip1=vtuner1 # skip /dev/misc/vtuner1 can also be vtunerN#fe_helper=/path/to/channellist # override frequency setup and use parameters from channellist # VDR channellists can be used here (eg. created by w_scan) # this somewhat guarantees high speed channel switching # when used with a lousy player # Astra 19.2 Channellist:
