Sundtek Support Forum
Deutsch => {Single, Dual, Quad} Sundtek SkyTV Ultimate => Thema gestartet von: Dr.Fack am Oktober 22, 2011, 11:16:21 Nachmittag
-
Vu+Duo mit 2 Sundtek SkyTV Ultimate (DVB-S/S2) geht das ?
ich habe gelesen es soll gehen wenn ja wie ?
cu
Dr.Fack ???
ein Sundtek SkyTV Ultimate (DVB-S/S2) habe ich laufen
-
Mehrfachtuner koennen ueber die Konsole konfiguriert werden.
cd /tmp
wget http://www.sundtek.de/support/multituner.sh
chmod 777 multituner.sh
./multituner.sh
Danach einfach neu starten.
-
hi irgent wie geht es nicht
root@bm750:~# cd /tmp
root@bm750:/tmp# wget http://www.sundtek.de/support/multituner.sh
Connecting to www.sundtek.de (85.10.198.106:80)
multituner.sh 100% |*******************************| 963 --:--:-- ETA
root@bm750:/tmp# chmod 777 multituner.sh
root@bm750:/tmp# ./multituner.sh
-sh: ./multituner.sh: not
-sh: ./multituner.sh: not found
root@bm750:/tmp# wget http://www.sundtek.de/support/multituner.sh
Connecting to www.sundtek.de (85.10.198.106:80)
wget: can't open 'multituner.sh': File exists
root@bm750:/tmp# chmod 777 multituner.sh
root@bm750:/tmp# ./multituner.sh
-sh: ./multituner.sh: not found
irgent was stimmt da nicht
was laüft falsch ?
-
Versuch's nochmal, das Skript ist aktuell nur auf einem PC getestet und dort ist der Interpreter anders.
Das alte Skript vorher löschen
cd /tmp
rm multituner.sh
-
Danke
jetzt hat es geklappt ;D
-
Hi
nach Stromausfall findet die VU den 2ten Sundtek SkyTV Ultimate (DVB-S/S2) nicht habe schon alles versucht
root@bm750:~# wget http://www.sundtek.de/support/multituner.sh
Connecting to www.sundtek.de (85.10.198.106:80)
wget: can't open 'multituner.sh': File exists
root@bm750:~# chmod 777 multituner.sh
root@bm750:~# ./multituner.sh
er findet aber immer nur ein Tuner
cu
Dr.Fack
-
Melde dich mal beim Support / "sundtek" Skype
-
haben die auch ne Mailadresse ? ???
-
was zeigt denn folgendes an:
/opt/bin/mediaclient -e
/opt/bin/mediaclient --lsusb
-
root@bm750:~# /opt/bin/mediaclient -e
Driver is currently not running, please start it as root
mediaclient --start
root@bm750:~# /opt/bin/mediaclient --lsusb
-
Der Treiber scheint ja nicht zu laufen, bitte die Installation einmal durchführen (insbesondere das Autostart bzw. Start Skript des Treibers ausführen)
http://wiki.sundtek.de/index.php/Dreambox
-
jetzt zeigt er das an :
root@bm750:~# /opt/bin/mediaclient -e
**** List of Media Hardware Devices ****
device 0: [Sundtek SkyTV Ultimate] DVB-S/S2, REMOTE-CONTROL
[SERIAL]:
ID: U110822153024
[DVB-S/S2]:
FRONTEND: /dev/dvb/adapter1/frontend0
DVR: /dev/dvb/adapter1/dvr0
-
und folgendes:
/opt/bin/mediaclient --lsusb
-
root@bm750:~# /opt/bin/mediaclient --lsusb
-
Gibt der Befehl denn nichts aus?
Ansonsten der:
cat /proc/bus/usb/devices
Stecken beide Sticks ordentlich an der Settopbox? Wenn nur einer erkannt wird dann ist wohl der 2. nicht richtig dran.
-
da wird jede menge angezeigt kann leider nicht alles copieren
oder gibt es da ein Trick ?
-
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-7.3 ohci_hcd
S: Product=BRCM OHCI
S: SerialNumber=ohci-brcm
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-7.3 ohci_hcd
S: Product=BRCM OHCI
S: SerialNumber=ohci-brcm
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-7.3 ehci_hcd
S: Product=BRCM EHCI
S: SerialNumber=ehci-brcm
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480
MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-7.3 ehci_hcd
S: Product=BRCM EHCI
S: SerialNumber=ehci-brcm
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=eb1a ProdID=51be Rev= 1.00
S: Manufacturer=Sundtek
S: Product=SkyTV Ultimate II
S: SerialNumber=U110927111220
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb_khelper
E: Ad=84(I) Atr=01(Isoc) MxPS= 0 Ivl=125us
I: If#= 0 Alt= 1 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb_khelper
E: Ad=84(I) Atr=01(Isoc) MxPS= 940 Ivl=125us
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=eb1a ProdID=51be Rev= 1.00
S: Manufacturer=Sundtek
S: Product=SkyTV Ultimate II
S: SerialNumber=U110822153024
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=84(I) Atr=01(Isoc) MxPS= 0 Ivl=125us
I: If#= 0 Alt= 1 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=84(I) Atr=01(Isoc) MxPS= 940 Ivl=125us
root@bm750:~#
-
Also wie das hier wieder aussieht hast du die vorigen Informationen nicht komplett ausgegeben.
/opt/bin/mediaclient -e muss viel mehr ausgeben als du da vorher angegeben hast.
cd /tmp
rm multituner.sh
wget http://www.sundtek.de/support/multituner.sh
chmod 777 multituner.sh
./multituner.sh
Anschliessend neu starten.
-
welcome on your Vu+ ! - Kernel 2.6.18-7.3 (#1 SMP Sat Oct 8 14:38:45 CEST 2011).
bm750 login:
root
root@bm750:~#
clear
[H[Jroot@bm750:~#
clear
[H[Jroot@bm750:~#
d
/tmp
-sh: d: not found
root@bm750:~# rm multituner.sh
root@bm750:~# wget http://www.sundtek.de/support/multituner.sh
Connecting to www.sundtek.de (85.10.198.106:80)
multituner.sh 0% | | 0 --:--:-- ETA
multituner.sh 100% |*******************************| 961 --:--:-- ETA
root@bm750:~# chmod 777 multituner.sh
root@bm750:~# ./multituner.sh
c
at /proc/bus/usb/devices
Multituner Support enabled
root@bm750:~#
c
at /proc/bus/usb/devices
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-7.3 ohci_hcd
S: Product=BRCM OHCI
S: SerialNumber=ohci-brcm
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-7.3 ohci_hcd
S: Product=BRCM OHCI
S: SerialNumber=ohci-brcm
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-7.3 ehci_hcd
S: Product=BRCM EHCI
S: SerialNumber=ehci-brcm
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480
MxCh= 2
B: Alloc=152/800 us (19%), #Int= 0, #Iso= 10
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-7.3 ehci_hcd
S: Product=BRCM EHCI
S: SerialNumber=ehci-brcm
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=eb1a ProdID=51be Rev= 1.00
S: Manufacturer=Sundtek
S: Product=SkyTV Ultimate II
S: SerialNumber=U110822153024
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb_khelper
E: Ad=84(I) Atr=01(Isoc) MxPS= 0 Ivl=125us
I: If#= 0 Alt= 1 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb_khelper
E: Ad=84(I) Atr=01(Isoc) MxPS= 940 Ivl=125us
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=eb1a ProdID=51be Rev= 1.00
S: Manufacturer=Sundtek
S: Product=SkyTV Ultimate II
S: SerialNumber=U110927111220
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb_khelper
E: Ad=84(I) Atr=01(Isoc) MxPS= 0 Ivl=125us
I: If#= 0 Alt= 1 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb_khelper
E: Ad=84(I) Atr=01(Isoc) MxPS= 940 Ivl=125us
root@bm750:~#
-
Danach noch cat /etc/sundtek.conf aber eigentlich sollte es nach dem Ausführen des Skripts und nach einem Neustart danach automatisch funktionieren.
-
ich habe die ariginal USB kabel ersetzt
jetzt geht es
danke für die Hilfe
cu
Dr-Fack ;D