Deutsch > {Single, Dual, Quad} Sundtek SkyTV Ultimate
SkyTV8 wird bei Tunen nicht mehr von Diskstation erkannt
Heinz:
Korrigiere: ./mediaclient --tsscan /dev/dvb/adapter0/dvr0 hat auch den Treiber abgeschossen. Nach der Ausgabe muss ich den Treiber neu starten.
Sundtek:
Was zeigt denn dmesg an?
Der Treiber wird wohl nur hängen wenn das USB Subsystem ihn irgendwie blockiert. Die Tests sind zudem einfacher wenn Du nur den (deiner Meinung nach) betroffenen Stick angeschlossen hast, ansonsten kommst Du damit eventuell durcheinander.
Heinz:
dmesg gibt einen langen Output, hier was ich zu USB finden konnte:
--- Code: ---[ 98.959587] Initializing USB Mass Storage driver...
[ 98.964907] usbcore: registered new interface driver usb-storage
[ 98.970944] USB Mass Storage support registered.
[ 99.133475] usbcore: registered new interface driver usblp
[ 99.588811] usbcore: registered new interface driver usbhid
[ 99.594470] usbhid: USB HID core driver
[ 104.311214] iSCSI: init_io_buffer_head(833) LUN-backup: 512 buffers allocated, total 2097152 bytes successfully
[ 110.348699] usb 2-1: USB disconnect, device number 2
[ 112.042619] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 114.061756] ata1.00: configured for UDMA/133
[ 114.066070] ata1: EH complete
[ 115.198821] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 115.276541] NFSD: starting 90-second grace period
[ 115.781724] ata2.00: configured for UDMA/133
[ 115.786036] ata2: EH complete
[ 126.061672] usb 2-1: new high-speed USB device number 3 using ehci_marvell
[ 136.835820] loop: module loaded
[ 147.121245] findhostd uses obsolete (PF_INET,SOCK_PACKET)
[ 163.795082] :eth0: link down
[ 163.798458] :eth0: link up, full duplex, speed 1 Gbps
[ 163.805232] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 175.568822] init: nmbd main process (8220) killed by TERM signal
[ 204.551998] init: nmbd main process (8855) killed by TERM signal
[ 260.504736] usbcore: registered new interface driver snd-usb-audio
[ 262.129119] usbcore: registered new interface driver snd-usb-hiface
[ 385.195821] init: pkg-synocalendar-notify-daemon main process (13104) killed by TERM signal
[ 385.570920] init: pkg-synocalendar-pushserver main process (12992) killed by TERM signal
[ 1156.977192] usb 2-1: USB disconnect, device number 3
[ 1188.285646] usb 2-1: new full-speed USB device number 4 using ehci_marvell
[ 1188.585725] usb 2-1: new high-speed USB device number 5 using ehci_marvell
[ 1188.817138] Got empty serial number. Generate serial number from product.
[ 1188.878071] hub 2-1:1.0: USB hub found
[ 1188.882153] hub 2-1:1.0: 4 ports detected
[ 1189.236050] usb 2-1.3: new high-speed USB device number 6 using ehci_marvell
[ 1189.712522] usb 2-1.3: USB disconnect, device number 6
[ 1190.261065] usb 2-1: USB disconnect, device number 5
[ 1190.605797] usb 2-1: new high-speed USB device number 7 using ehci_marvell
[ 1190.847138] Got empty serial number. Generate serial number from product.
[ 1190.915967] hub 2-1:1.0: USB hub found
[ 1190.920029] hub 2-1:1.0: 4 ports detected
[ 1191.776171] usb 2-1.4: new high-speed USB device number 8 using ehci_marvell
[ 2286.086308] usb 2-1: USB disconnect, device number 7
[ 2286.091312] usb 2-1.4: USB disconnect, device number 8
[ 2286.523263] usb 2-1: new high-speed USB device number 9 using ehci_marvell
[ 2288.303381] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 2302.924121] usb 2-1: new high-speed USB device number 10 using ehci_marvell
[ 2307.514363] usb 1-1: new high-speed USB device number 2 using ehci_marvell
--- Ende Code ---
Betroffen sind beide Karten, aber ich stecke die MediaTV 3 erstmal aus.
Heinz:
Ich habe zwischenzeitlich auch mit einem aktiven USB-Hub getestet, da ich einen Fehler in der USB-Stromversorgung vermutete. Aber auch mit diesem legt die Karten das gleiche Verhalten an Tag.
Heinz:
Leider komme ich nicht weiter. Gibt es eine andere Möglichkeit den Fehler einzugrenzen?
Navigation
[0] Themen-Index
[#] Nächste Seite
[*] Vorherige Sete
Zur normalen Ansicht wechseln