Sundtek Support Forum
English => VU+ - VU Duo Settopbox => Thema gestartet von: DaMacFunkin am Oktober 30, 2015, 06:09:14 Nachmittag
-
Hello I now have Solo4k as well as Duo2 and Solo2.
Do you have plug in and drivers for your products for New Solo4k?
If so does it work on VTI 9, they are the only image at the moment.
Thank you.
-
For sure we have a driver for it but I don't think that the installer will detect it as a settopbox. It will just detect it as ARM system.
Can you contact us via Skype so we can update the installer script to detect your system as settopbox?
-
I'm sorry I do not Skype, is there some other way for me to provide the information you require?
-
can you join the chatroom tomorrow?
http://chat.sundtek.de
if that one causes issues for you - you might use an alternative chat:
http://webchat.freenode.net
Channel #sundtek
-
Yes what time? I can be available from 9 am GMT.
-
Hello, i am on chat now.
-
The next driver update later today will have full support for the solo4k. I have set it up manually for now on your system.
-
my box has just locked up again like it did before, i changed channel to check if the video was smooth because it looked a little bit twitchy and after a few seconds it has locked up?
-
It rebooted from telnet command, will continue to test.
-
if you keep having issues join the chat again.
-
box has locked up again, i am on chat now.
-
Ok seems like the settopbox does not like the infrared support of our tuner (just like all the other VU+ settopboxes). I disabled it for now. The next driver update will disable it for all Sundtek devices for that new Settopbox.
USB Tuner Infrared Support is not needed anyway since you are using the original settopbox infrared.
The problem is that the USB Controller driver of the VU+ settopbox cannot handle USB interrupt transfers properly - which the USB tuner is using.
However for using the tuner it's all no problem since you only want the video data from it.
-
I have to tell you I have another problem, I powered box off and inserted sundtek sky dvb-s2 stick and the box would not boot with both USB tuners plugged in.
I turned box off, unplugged -s2 stick and box booted fine with dvb-c still installed.
-
Let's wait for the update which disables the IR support on that settopbox first because the DVB-S/S2 tuner is still affected by this problem on your side.
The IR support is loaded as soon as the driver is loaded - even before engima2.
-
the driver has been updated.
-
Hello I have installed new driver from sundtek control centre, the box will not boot with DVB-S2 version IV (upgraded) plugged in, either on its own or with dvb-c.
Box boots fine with 2 DVB-C attached.
Please advise.
-
Also I have found if you configure plug in for 2 sticks, then power off, remove one stick and reboot the box won't boot.
You need to boot with none, configure plug in not to auto start, power off, attach single tuner then restart.
-
update to the latest driver, if you still have issues with it join the chat again to check what's going on.
-
Hello, i am in chat for short while.
Off work today.
-
Hello, i seem to have got it working.
I started enigma2 with the DVB-C/T2 attached only, when enigma2 started i then plugged in DVB-S2 tuner, opened Sundtek control panel and configured second tuner.
On pressing Blue button enigma2 restarted and the tuner is present, i will test during the day.
So if tuners in slots does not match last config enigma 2 does not boot.
I have to go out this morning, if you want to have a fine tune of the plug in this afternoon then i may be avilable.
Please let me know.
-
The previous driver installer created adapter1 (as you might remember), I updated the installer script yesterday evening now it won't create the additional adapter anymore if you update the driver. I guess that might have been the issue.
If you are still able to reproduce the problem please do so and contact us via Chat to check what's going on.