sundtek control center enigma2

[jteeuw]

I use the latest sundtek control center enigma2 for my xtrend 8000
The Sundtek usb dongle is connected to my QNAP

Everthing is working but when i reboot my xtrend reciever, the enigma 2 software does not automount the Sundtek dongle.

i have to run /opt/bin/mediaclient --mount=192.168.1.200 on the reciever tt get everthing working.

Is there a automount option in sundtek control center enigma2

thanks

[Sundtek]

Did you set the driver to autostart in the sundtek control center?

[jteeuw]

Driver is set to autostart, this is my sundtek.conf :

# sundtek configuration file - /etc/sundtek.conf
# created / modified: Jul 08 2014, 19:25h by sundtekcontrolcenter 1.4.0-20140223-r2

loglevel = off
autoupdate = off
dmhwpidfilter = off
vtuner_acceleration = off
enablenetwork = off

###### configuration network
[NETWORK]
device=192.168.1.200:0

###### configuration stick 1
[U120105091633]
netrecoverymode=on
initial_dvb_mode=DVBC
dreambox_support_fe1=on

[Sundtek]

The configuration looks okay, can you make a screenshot that shows that the driver is set to autostart in the sundtek control center?

Last time I tested it with our DM800HD SE it worked without any problems.

Also is your device visible via network? eg. what is the output of following command when you start it on the settopbox:
/opt/bin/mediaclient --scan-network

[jteeuw]

------------------------------------------------------------------------------
 IP address       | ID  |  devicename          | Users | Capabilities | Serial
------------------------------------------------------------------------------
 192.168.1.200    | 0   | Sundtek MediaTV Digital Home (USB 2.0)  | 40   | DVB-T                                                     , DVB-C | U120105091633
-  1 IPTV server found -------------------------------------------------------

[Sundtek]

Can you make a screenshot of the sundtek control center?

and cat /proc/bus/nim_sockets

by the way if you want the answers a little bit quicker just contact us via Skype (sundtek)

[jteeuw]

root@et8000:~#  cat /proc/bus/nim_sockets
NIM Socket 0:
        Type: DVB-C
        Name: TDA10024
        Has_Outputs: yes
        Frontend_Device: 0
        I2C_Device: 3
NIM Socket 1:
        Type: DVB-C
        Name: Sundtek DVB-C (192.168.1.200) (USB)
        Has_Outputs: no
        Frontend_Device: 1
        I2C_Device: -1
NIM Socket 2:
        Type: DVB-C
        Name: Sundtek DVB-C (192.168.1.200) (USB)
        Has_Outputs: no
        Frontend_Device: 2
        I2C_Device: -1

[jteeuw]

after a reboot :


root@et8000:~#  cat /proc/bus/nim_sockets
NIM Socket 0:
        Type: DVB-C
        Name: TDA10024
        Has_Outputs: yes /opt/bin/mediaclient --mount=192.168.1.200

        Frontend_Device: 0
        I2C_Device: 3


Then i run /opt/bin/mediaclient --mount=192.168.1.200 with output :
driver is possibly not started, trying to start now...
Successfully mounted: 192.168.1.200

then  cat /proc/bus/nim_sockets gives the following output :
NIM Socket 0:
        Type: DVB-C
        Name: TDA10024
        Has_Outputs: yes
        Frontend_Device: 0
        I2C_Device: 3
NIM Socket 1:
        Type: DVB-C
        Name: Sundtek DVB-C (192.168.1.200) (USB)
        Has_Outputs: no
        Frontend_Device: 1
        I2C_Device: -1
NIM Socket 2:
        Type: DVB-C
        Name: Sundtek DVB-C (192.168.1.200) (USB)
        Has_Outputs: no
        Frontend_Device: 2
        I2C_Device: -1

[Sundtek]

Hi,

this is not correct, do you have 2 network devices or only one?

[jteeuw]

Hi,

I have one network deices

[Sundtek]

Can you contact us via Skype chat (sundtek)?

I was just wondering because you loaded the network device twice.

[jteeuw]

Hi ,
I am not able to skype , can i provide some other information ?

[Sundtek]

http://chat.sundtek.de how about that?

[jteeuw]

I joinend http://chat.sundtek.de

[jteeuw]

I did a ./sundtek_netinst.sh –u
Then go to the control center and start the driver

But I get e error :